Home
》》》》》》》1
Maya 3D Tutorial Modeling - Sword Thu Oct 09, 2014 2:05 am
Admin
Admin
[You must be registered and logged in to see this image.]
1, draw a curve and replicate adjustment, then loft operating surface, and adjust the surface point to Figure.
\
Click to enlarge
First, look at the renderings.
\
1, draw a curve and replicate adjustment, then loft operating surface, and adjust the surface point to Figure.
\
Click to enlarge
4, using a cut command.
\
Click to enlarge
5, cut as shown, select the two surfaces cut edges, use the command a rounded tool.
\
Click to enlarge
6, were shown round after the operation, select ISO curved bottom line, use the command one, copy the curve and move the zoom to the powder line position.
\
Click to enlarge
7, two curved surfaces were selected ISO cable, connect using freeform fillet.
\
Click to enlarge
8, adjust the zoom point connection to the position on the surface.
\
Click to enlarge
9, the upper and lower surfaces were selected chain ISO line, use the command a curvature softer.
\
Click to enlarge
10, create a polygon cylinder, choose to use the command shown face a face to stretch the right position.
\
Click to enlarge
11, delete the intermediate surface records, and pull points lengthened surface.
\
Click to enlarge
12, create two circular command a stakeout operation.
\
Click to enlarge
13, after selecting two surfaces created using the command a fillet.
\
Click to enlarge
14, if the round fails, ctrl + a to open the surface properties of the value to a negative value.
\
Click to enlarge
15, were cut.
\
Click to enlarge
16, to create a BOX conduct a Boolean operation.
\
Click to enlarge
17, to create a copy scaling curve, use the command mapped onto a surface, and then select the cut after cut, stretch.
\
Click to enlarge
18, select the sheared surface, use the command an inward migration, and then use the command 2.
\
Click to enlarge
19, after selecting two surfaces ISO line fillet operation.
\
Click to enlarge
20, to create a cylinder, mapping curve to the surface, and then cut.
\
Click to enlarge
21, create a polygon cylinder, select the face as shown stretched.
\
Click to enlarge
22, be smooth.
\
Click to enlarge
23, select the above ISO line, use the command to create a surface.
\
Click to enlarge
24, select Move and zoom Surfaces, select the ISO cable to connect the two.
\
Click to enlarge
25, converted to a polygonal surface.
\
Click to enlarge
26, select the face stretched.
\
Click to enlarge
27, as shown in the middle of a little no merger, choose two tools an operation.
\
Click to enlarge
28, delete the history.
\
Click to enlarge
29, select the surface tension, as shown.
\
Click to enlarge
30, drawing curves, and rotated.
\
Click to enlarge
31, between the surface fillet and cut the desired surface.
\
Click to enlarge
32, the curve is rotated, adjusted to FIG.
\
Click to enlarge
33, to create a surface mapping and cut.
\
Click to enlarge
34, copy surfaces intersect, and cut out the bottom surface of the need.
\
Click to enlarge
35, to create a plane and mapping curve cut.
\
Click to enlarge
36, choose two vertical HULL adjusted.
\
Click to enlarge
37, select the ISO conducted on both sides of the connection.
\
Click to enlarge
38, the curve mapping and cut.]
1, draw a curve and replicate adjustment, then loft operating surface, and adjust the surface point to Figure.
\
Click to enlarge
First, look at the renderings.
\
1, draw a curve and replicate adjustment, then loft operating surface, and adjust the surface point to Figure.
\
Click to enlarge
4, using a cut command.
\
Click to enlarge
5, cut as shown, select the two surfaces cut edges, use the command a rounded tool.
\
Click to enlarge
6, were shown round after the operation, select ISO curved bottom line, use the command one, copy the curve and move the zoom to the powder line position.
\
Click to enlarge
7, two curved surfaces were selected ISO cable, connect using freeform fillet.
\
Click to enlarge
8, adjust the zoom point connection to the position on the surface.
\
Click to enlarge
9, the upper and lower surfaces were selected chain ISO line, use the command a curvature softer.
\
Click to enlarge
10, create a polygon cylinder, choose to use the command shown face a face to stretch the right position.
\
Click to enlarge
11, delete the intermediate surface records, and pull points lengthened surface.
\
Click to enlarge
12, create two circular command a stakeout operation.
\
Click to enlarge
13, after selecting two surfaces created using the command a fillet.
\
Click to enlarge
14, if the round fails, ctrl + a to open the surface properties of the value to a negative value.
\
Click to enlarge
15, were cut.
\
Click to enlarge
16, to create a BOX conduct a Boolean operation.
\
Click to enlarge
17, to create a copy scaling curve, use the command mapped onto a surface, and then select the cut after cut, stretch.
\
Click to enlarge
18, select the sheared surface, use the command an inward migration, and then use the command 2.
\
Click to enlarge
19, after selecting two surfaces ISO line fillet operation.
\
Click to enlarge
20, to create a cylinder, mapping curve to the surface, and then cut.
\
Click to enlarge
21, create a polygon cylinder, select the face as shown stretched.
\
Click to enlarge
22, be smooth.
\
Click to enlarge
23, select the above ISO line, use the command to create a surface.
\
Click to enlarge
24, select Move and zoom Surfaces, select the ISO cable to connect the two.
\
Click to enlarge
25, converted to a polygonal surface.
\
Click to enlarge
26, select the face stretched.
\
Click to enlarge
27, as shown in the middle of a little no merger, choose two tools an operation.
\
Click to enlarge
28, delete the history.
\
Click to enlarge
29, select the surface tension, as shown.
\
Click to enlarge
30, drawing curves, and rotated.
\
Click to enlarge
31, between the surface fillet and cut the desired surface.
\
Click to enlarge
32, the curve is rotated, adjusted to FIG.
\
Click to enlarge
33, to create a surface mapping and cut.
\
Click to enlarge
34, copy surfaces intersect, and cut out the bottom surface of the need.
\
Click to enlarge
35, to create a plane and mapping curve cut.
\
Click to enlarge
36, choose two vertical HULL adjusted.
\
Click to enlarge
37, select the ISO conducted on both sides of the connection.
\
Click to enlarge
38, the curve mapping and cut.]
